Grade | Variation of ball diameter µm VDWS |
Deviation from spherical form µm |
Surface roughness µm |
Lot diameter variation µm VDWL |
Gage interval µm |
Allowable ball gage deviation µm |
Sub-gage interval µm |
Allowable ball sub-gage deviation µm |
---|---|---|---|---|---|---|---|---|
3 | 0.08 | 0.08 | 0.010 | 0.13 | 0.5 | +/-5 | 0.1 | +/-0.2 |
5 | 0.13 | 0.13 | 0.014 | 0.25 | 1 | +/-5 | 0.2 | +/-0.4 |
10 | 0.25 | 0.25 | 0.020 | 0.5 | 1 | +/-9 | 0.2 | +/-0.4 |
16 | 0.40 | 0.40 | 0.025 | 0.8 | 2 | +/-10 | 0.4 | +/-0.8 |
20 | 0.50 | 0.50 | 0.032 | 1 | 2 | +/-10 | 0.4 | +/-0.8 |
24 | 0.60 | 0.60 | 0.040 | 1.2 | 2 | +/-12 | 0.4 | +/-0.8 |
28 | 0.70 | 0.70 | 0.050 | 1.4 | 2 | +/-12 | 0.4 | +/-0.4 |
40 | 1.00 | 1.00 | 0.060 | 2 | 4 | +/-16 | 0.8 | +/-1.6 |
60 | 1.50 | 1.50 | 0.080 | 3 | 6 | +/-18 | 1.2 | +/-2.4 |
100 | 2.50 | 2.50 | 0.100 | 5 | 10 | +/-40 | 2.0 | +/-4.0 |
200 | 5.00 | 5.00 | 0.150 | 10 | 15 | +/-60 | 3.0 | +/-6.0 |
Grade | Allowable ball diameter variation µm VDWS |
Allowable deviation from spherical form µm ΔRV |
Maximum surface roughness arithmetic average µm Ra |
Allowable lot diameter variation µm VDWL |
Nominal ball deviation tolerance µm |
Allowable ball gage marking µm ΔRS |
Container marking increment µm |
---|---|---|---|---|---|---|---|
48 | 1.2 | 1.2 | 0.08 | 2.4 | - | - | - |
3 | 0.08 | 0.08 | 0.012 | 0.13 | - | ±0.75 | 0.25 |
5 | 0.13 | 0.13 | 0.02 | 0.25 | - | +1.25/-1 | 0.25 |
10 | 0.25 | 0.25 | 0.025 | 0.5 | - | +1.25/-1 | 0.25 |
16 | 0.4 | 0.4 | 0.025 | 0.8 | - | +1.25/-1 | 0.25 |
24 | 0.6 | 0.6 | 0.05 | 1.2 | - | ±2.5 | 1.25 |
100 | 2.5 | 2.5 | 0.125 | 5 | ±12.5 | - | - |
200 | 5 | 5 | 0.2 | 10 | ±25 | - | - |
500 | 13 | 13 | - | 25 | ±50 | - | - |
1000 | 25 | 25 | - | 50 | ±125 | - | - |
Grade | Dw | Tolerances on one ball | Lots tolerances | |||||||
---|---|---|---|---|---|---|---|---|---|---|
Nominal size in mm over up to |
Limit deviations µm |
Ball dia. variation (µm) VDWS |
Deviation from spher. form (µm) tDW |
Surface roughness (µm) Ra |
Lots dia. variation (µm) VDWL |
Gages deviation µm |
Gages interals µm |
Ball gage tolerances | ||
3 | - | 12 | ±5.32 | 0.08 | 0.08 | 0.010 | 0.13 | -5/+5 | 0.5 | 0.5 |
5 | - | 12 | ±5.63 | 0.13 | 0.13 | 0.014 | 0.25 | -5/+5 | 1 | 1 |
10 | - | 25 | ±9.75 | 0.25 | 0.25 | 0.020 | 0.5 | -9/+9 | 1 | 1 |
16 | - | 25 | ±11.4 | 0.4 | 0.4 | 0.025 | 0.8 | -10/+10 | 2 | 2 |
20 | - | 38 | ±11.5 | 0.5 | 0.5 | 0.032 | 1 | -10/+10 | 2 | 2 |
28 | - | 50 | ±13.7 | 0.7 | 0.7 | 0.050 | 1.4 | -12/+12 | 2 | 2 |
40 | - | 100 | ±19 | 1 | 1 | 0.060 | 2 | -16/+16 | 4 | 4 |
100 | - | 150 | ±47.5 | 2.5 | 2.5 | 0.125 | 5 | -40/+40 | 10 | 10 |
200 | - | 150 | 72.5 | 5 | 5 | 0.200 | 10 | -60/+60 | 15 | 15 |
500 | - | 25 | ±75 | 25 | 25 | - | 50* | -50/+50 | 50 | 50 |
500 | 25 | 50 | ±112.5 | 25 | 25 | - | 75* | -75/+75 | 75 | 75 |
500 | 50 | 75 | ±150 | 25 | 25 | - | 100* | -100/+100 | 100 | 100 |
500 | 75 | 100 | ±187.5 | 32 | 32 | - | 125* | -125/+125 | 125 | 125 |
500 | 100 | 125 | ±225 | 38 | 38 | - | 150* | -150/+150 | 150 | 150 |
500 | 125 | 150 | ±262.5 | 44 | 44 | - | 175* | -175/+175 | 175 | 175 |
600 | All | All | ±200 | - | - | - | 400* | - | - | - |
700 | All | All | ±1000 | - | - | - | 2000* | - | - | - |
1 | 2 | 3 | 4 | 5 | 6 | 7 | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Class | Diameter (nominal) mm |
Allowance on diameter µm |
Tolerance in each grade µm |
Mean allowances in each grade (µm) | Permissible geometrical deviation µm |
Example of applications | ||||||||||
I | Up to 10 | ±10.25 | 0.5 | -10 | ... | -1.5 | -1 | -0.5 | 0 | +0.5 | 1 | +1.5 | ... | +10 | 0.25 | Ball bearings precision turntables high pressure closures |
II | Up to 25 | ±10.50 | 1 | -10 | ... | -3 | -2 | -1 | 0 | +1 | +2 | +3 | ... | +10 | 0.5 | |
III | Up to 25 | 2 | -10 | -8 | -6 | -4 | -2 | 0 | +2 | +4 | +6 | +8 | +10 | 1 | ||
25 to 50 | 3 | -12 | -9 | -6 | -3 | 0 | +3 | +6 | +9 | +12 | 1.5 | |||||
50 to 75 | 4 | -12 | -8 | -4 | 0 | +4 | +8 | +12 | 2 | |||||||
75 to 100 | 5 | -15 | -10 | -5 | 0 | +5 | +10 | +15 | 2.5 | |||||||
100 to 125 | 6 | -18 | -12 | -6 | 0 | +6 | +12 | +18 | 3 | |||||||
125 to 150 | 7 | -21 | -14 | -7 | 0 | +7 | +14 | +21 | 3.5 | |||||||
IV | Up to 10 | ±14 | 4 | -12 | -8 | -4 | 0 | +4 | +8 | +12 | 2 | Hub bearings | ||||
V | Up to 25 | ±75 | 50 | -50 | 0 | +50 | 25 | Turables for road vehicles furniture castors, lubricators, sping loaded catches | ||||||||
25 to 50 | ±113 | 75 | -75 | 0 | +75 | 38 | ||||||||||
50 to 75 | ±150 | 100 | -100 | 0 | +100 | 50 | ||||||||||
75 to 100 | ±188 | 125 | -125 | 0 | +125 | 63 | ||||||||||
100 to 125 | ±255 | 150 | -150 | 0 | +150 | 75 | ||||||||||
125 to 150 | ±263 | 175 | -175 | 0 | +175 | 88 | ||||||||||
VI | ±200 | 400 | Ball mills, mill charges |
青岛百克滚珠传动部件有限公司
Qingdao BRBC Balls & Transmission Parts Co., Ltd.
921 Tuanjie Road
Economic and Technological Development Zone
Qingdao, Shandong Province
Tel: (+86-532) 8610 7680
Fax: (+86-532) 8610 7682
Email: contact@brbc.cn